JETDIRECT 170X MANUAL PDF

Very nice blog Hot Tot Hair Products seems to be very useful I would like to try them if i could buy them in Australia Nice work, keep it up. Printer Install , Printer setup. Energy , Setup Biz.

Author:Malazragore Samusho
Country:Andorra
Language:English (Spanish)
Genre:Science
Published (Last):5 October 2004
Pages:271
PDF File Size:1.2 Mb
ePub File Size:4.81 Mb
ISBN:801-2-77324-164-7
Downloads:19430
Price:Free* [*Free Regsitration Required]
Uploader:Faehn



Manual zz. All rights reserved. For warranty service information, see appendix C at the back of this manual. Reproduction, adaptation or translation without prior written permission is prohibited, except as allowed under the copyright laws. November Safety Considerations Applicable Products: Prior to the installation and use of this product, review all safety markings and instructions. Ethernet is a registered trademark of Xerox Corporation. Warranty The information contained in this document is subject to change without notice.

Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance or use of this material. A copy of the specific warranty terms applicable to your HP product and replacement parts can be obtained from your HP Sales and Service Office or Authorized dealer. Customer Support! Instruction Manual Symbol. If the product is marked with this symbol, refer to the product manuals to protect the product from damage.

Any service, adjustment, maintenance, or repair of this product must be performed only by authorized service-trained personnel. These products do not have a power switch; they are powered on when either the power cord or AC adapter is plugged into a power outlet. The power outlet shall be installed near the equipment and shall be easily accessible for quick disconnect. A-1 Power Requirements.

A-2 Environmental. A-4 Acoustic Noise. A-4 Electromagnetic Emissions. A-4 Safety. B-1 European Community. B-1 Declaration of Conformity. The external print servers enhance workgroup capability by letting you place your printers, plotters, or HP All-in-One peripherals1 at convenient locations directly on the network, and by increasing network printer performance and management.

The one-port print servers connect one printer, plotter, or All-in-One peripheral with a parallel port to the network. These print servers have one high-speed, bidirectional parallel port IEEE standard that supports multiple network operating systems NOSs Figure 1.

Figure 1. Each port operates independently which, in effect, gives you three print servers in one Figure 1. The X connects up to three printers, plotters, or HP All-in-One peripherals with parallel ports to a network. To connect a serial printer, use a parallel-to-serial adapter. These print servers also collect network statistics and error messages to aid in network management and troubleshooting. A standard SNMP agent resides on these print servers.

Any standard SNMP-based application can be used to access and manage these print servers. IEEE And the Activity LED is Then the print server is Off Off Not receiving power. Off On Solid Encountering a fault during self-test or operation. On; heavy LAN activity detected. See Chapter 2 for more information. If the 10 left LED is And the right LED is Then the print server has Off Off No link established. On Off Link established at 10 Mbps. Off On Link established at Mbps.

The factory-default setting of all 3 switches down will suit most installations. When the first switch is set to Auto, the other two switch settings are ignored; the server auto-negotiates the link speed and duplex setting with the connected switch or hub device.

Although nearly always unnecessary, you can control the settings directly by positioning the switches as shown in the table below, only if you are certain of the duplex setting and speed at which the switch or hub is operating. If the auto switch is set to And if the speed switch is set to And if the duplex switch is set to Then the settings are See p. Connect the print server to the network and printer s and plug in the print server.

Generate a configuration page from the print server. After you install the print server, the next step will be to configure it. Follow these instructions to install the HP JetDirect external print servers. Switch off the power for each printer. To do this, take a pen or similar object and slide the switch up for 16 Mbps or down for 4 Mbps.

Data-rate switch Figure 2. For the X or X Ethernet print servers JA or JA , verify that the auto-negotiation switches are in their default positions—all down. For other options, see page Figure 2. Since there is no power switch, the print server is switched on after you plug it in. Check the LEDs on the front of print server. The Status LED should be green—either steady or blinking. For troubleshooting information, see the Troubleshooting chapter in the software guide shipped with your print server.

Switch on the power on your printer s to begin printing. Verifying the Hardware Installation To verify the installation of the HP JetDirect external printer server, generate a configuration page.

This page is generated from Port 1 of the printer server. To generate a configuration page, follow these steps: 1. Print a configuration page by pressing and releasing the Test button on the print server. The printer language is auto-detected the first time the print server is powered up and after each cold reset.

Hardware Installation Hardware 2 Installation Wait about 10 seconds. When you hold down the Test button for three seconds, the LEDs begin to cycle through four configurations, as outlined in the following table. Release the Test button when you get the right PDLs, and the configuration page will be printed. For PDL The Status LED is Then they switch off, indicating they are cycling through the PDLs.

Resetting to Factory Defaults Once you have configured the HP JetDirect external print server, the configuration settings are retained in memory unless you manually reset them. The firmware is not affected when you reset the configuration settings. To reset the configuration settings to their factory defaults, follow these steps: 1. Unplug the power cord from the print server. While holding down the Test button on the print server, plug the power module into the print server and continue to hold down the Test button for five seconds.

All previous configuration settings will be erased. JA mm 7. JA mm 11 in. JB mm 7. Country Part Num. Part Num. These limits are designed to provide reasonable protection against interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio communications.

Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at their own expense. Pursuant to Part The Federal Communications Commission has prepared a booklet titled Interference Handbook , which may be helpful to you.

This booklet stock number may be purchased from the Superintendent of Documents, U. Government Printing Office, Washington, D. Note This is a class A product.

GAMOW MR TOMPKINS PDF

HP Jetdirect 170x Print Server series Manuals

How to control your HP Jetdirect x. How to control your HP Jetdirect x This step by step instruction describes how to setup a HP Jetdirect x print server so that the 8 bits output can be controlled by a user made program or from a PHP script. To make a fresh start you can factory reset the Jetdirect x. Procedure as follows: 1. Unplug the power to the Jetdirect.

GITARREN SCHLAGTECHNIK PDF

HP Jetdirect 170x Ethernet Print Server Manuals

Quick Links. Download this manual See also: Appendix. HP JetDirect. Table of Contents.

Related Articles